TROPIC ROOFING

Press

Silicone Myths - BUSTED

Published April 10th, 2018 by Edward Leshansky

4 Common Silicone Myths - BUSTED  by Jeremy Grunewald, R&D Manager

Silicone Myths: BUSTED

Jeremy Grunewald, R&D Manager Tropical Roofing Products

 

  1. Silicone Roof Coatings are “Waterproof”
  2. “Nothing Sticks to Silicone”
  3. Silicone Coatings are “better” than Acrylic Coatings
  4. 100% Silicone Coatings are 100% Solids

  1. Silicone Roof Coatings are Waterproof. This is the most common misleading and incorrect term associated with silicone roof coatings, “silicones.” The correct terminology is that silicones are water-resistant, or more specifically water-repellent. The term waterproof is defined as inherently being impervious to water; water cannot penetrate the membrane or coating. All silicones on the market today possess some level of permeability, typically 3.0-12.0 perms, which allow water vapors to permeate through the coating due to forces from hydrostatic pressure.

Silicones are designed to hold ponded water, which the National Roofing Contractors Association (NRCA) defines as holding pooling water for 48 hours. It is in the very nature of roof coatings to be permeable and allow trapped moisture in the decking, insulation, or underlayment to evaporate allowing the building to breathe. If silicones find themselves in ponded water circumstances for periods longer than 48 hours, water begins to penetrate the coating and make its way to the underlying membrane or coating which may result in coating delamination, adhesive failure, telegraphing, or blistering. Roofing systems are waterproof due to the type of membranes or barriers that are underneath the silicone coating. However, even the best of the silicones by themselves are not waterproof.

  1. “Nothing Sticks to Silicone.” Though this may be seen time and time again in the field, this is a myth that has been perpetuated for years. It is true that asphaltic and bitumous mastics, cements, coatings, and emulsions as well as water or solvent borne acrylics, polyurethanes, and even Sprayed-in-place Polyurethane Foams (SPF) do not have positive adhesion to silicone coatings so it is understandable where the myth came from.

To put some brief science and explanation behind the phenomenon, silicone films have lower surface energies than most other coating types in the market place, coming in around 20-30 dynes/cm. For reference, Teflon™ and non-stick coatings are around 18 dynes/cm whereas acrylic and epoxy coatings tend to be closer to 40-50 dynes/cm.The lower the substrate surface energy, the more difficult it is to adhere to the substrate, i.e. silicones have low surface energy so they are difficult to adhere to. This means that silicone surfaces, once cured, are very slick and slippery as you can experience by walking on a silicone roof in the morning before the dew has evaporated or after a recent rain storm.

The answer is knowing which silicone coatings in the market place have low surface energies so that they can stick to other higher surface energy silicones and coatings. It is important to be aware that certain silicone technologies in the market do adhere to existing and new silicone coatings. We are of the age where this myth can be put to rest as current, market available technologies and coatings exist, such as Tropical Roofing Products’ 924 Eterna-Sil Premium Silicone Roof Coating, overcoming and “busting” this myth.

  1. Silicone Roof Coatings are “Better” than Acrylic Roof Coatings. More than just an opinion, this idea has proliferated the roof coatings industry for nearly a decade. As one may guess, opinions aside, there are pros and cons that exist for both silicone and acrylic roof coatings. Silicone coatings show greater resistance to ponded water areas than do acrylic coatings while acrylic coatings have greater Dirt Pickup Resistance (DPR) and much greater tear resistance than their silicone counterparts. There is a time and place for both technologies. Below is a short analysis of when and where to use either coating to gain the most benefit out of your maintenance and restoration coating choice - silicone or acrylic.

Generally, positively sloped roofs with inclines greater than 1/12 are excellent candidates for acrylic top coats. Roofing terrains that exhibit positive, sound slope and drainage across the roofing system, likely do not have large ponded areas and as a result there is no need to utilize a silicone coating for the entire system. The benefits of a brighter and whiter coating can be realized due to the greater DPR and harder film of the acrylic coating. The coating is more durable and less likely to be damaged from hail, foot-traffic, and/or debris from storms and winds. In those low-lying areas where ponding may occur, silicone coatings may be used in a hybrid type manner as a patch over those areas but the remainder of the roof can be coated with the acrylic coating. This will allow the roof coating system to be “tailor-made” and custom to that specific roof, utilizing the strengths of both the acrylic and silicone coating together. Every building and roof is unique and has its own story to tell, so why not the maintenance and restoration system?

Near dead-flat and low-sloped roofs with inclines less than 1/24 (½:12) should immediately call into mind the need for a more water-resistant solution than an acrylic top coat. Areas with very low slope, less than 1/24, are highly susceptible to ponding and a silicone coating should be considered. Acrylic coatings under ponded conditions will likely swell and blister causing water intrusion underneath the coating, leading to potential leaks in the roofing system and coating delamination.

If the low-sloped roof exhibits no signs of ponded water and there is adequate, positive drainage then either coating type is likely a candidate to consider. There are downsides and upsides of both coatings to consider from a cost, labor, and application standpoint; however, from a performance perspective, silicone coatings have better ponded water resistance and acrylic coatings have far superior tear resistance, greater durability, and greater DPR performance.

  1. 100% Silicone Coatings are 100% Solids. High solids silicones are made with 100% silicone polymers that are not diluted down with any types of solvents, at least that is what the labels would lead you to believe. Upon further inspection, most high solids silicones are on average 90-96% solids by volume. There is no definition to what separates high solids silicones from their lower solids counter parts. This is a relative term that implies only that high solids silicones are greater in solids content than their solvent diluted versions, the “low-solids” or “solvent-based” silicones at around 70-80% solids by volume.

Many of the market available high solids silicones contain a small portion of VOC exempt solvents or other chemicals diluting them to these lower 90% values. These solvents may be added for a variety of reasons, for instance to help with adhesion or to help thin out the coating. 100% silicone simply refers to the quality of the silicone polymer that is used in the coating which ultimately only takes up only a fraction of what the entire coating is made from. The rest of the coating is filled with pigments and other chemicals that aid in cure speed, adhesion, and other performance characteristics that make each coating unique. This “chemical finger print” differentiates each silicone coating allowing each coatings brand manufacturer to stand apart from the rest.

Tropical Roofing Products’ 924 Eterna-Sil Premium Silicone Roof Coating is a 95% volume solids product and offers the most unique and advanced chemical finger print in the coatings industry. Formulated and designed specifically for direct-bond adhesion to all common roofing substrates including existing and aged silicone, falling shy of the impossible 100% volume solids, is a necessary trade to achieve the greatest adhesion performance in the industry.

For technical inquiries on roof coatings technology including our new Eterna-Sil series of silicone products, please contact us for more information.

Jeremy Grunewald

Corporate R&D Manager

jeremy@gotropical.com

 

What Type of Roof Coating is Best?

Published May 2nd, 2017 by Edward Leshansky

See Tropical Roofing Products own Keith Borden quoted in this recent article in Facilities Net: http://www.facilitiesnet.com/roofing/article/What-Type-of-Roof-Coating-is-Best--17137?source=previous

 

TROPICAL ROOFING PRODUCTS ADDS NEW GREAT WHITE ELASTOMERIC MASTIC

Published March 27th, 2017 by Edward Leshansky

HALLANDALE, FL – Tropical Roofing Products, a leading manufacturer of Fluid Applied Restoration Solutions including a wide portfolio of repair and maintenance coatings, mastics, and adhesives continues its tradition of innovation for the professional roofing industry with the introduction of #979 Great White Elastomeric Mastic.

#979 Great White, as the name implies, is a white solvent based, fiber reinforced SEBS modified rubber mastic formulated to repair modified bitumen, metal, concrete, and some single ply membranes. Great White is perfect for wet or dry repairs and can confidently be applied as an underwater repair mastic.

Highly reflective #979 Great White reinforced mastic possesses cold weather pliability, strong water resistance, and good chemical resistance.  #979 Great White is available in two formulas.  The 979 LOW VOC formula complies with SCAQMD rule 1113.

For more information on Tropical Roofing Products, or to find your closest representative, call 800-432-2855 or visit www.tropicalroofingproducts.com. Download the Tropical Roofing Products dynamic mobile app by texting “ROOFING” to 94502 or visit the app store for your mobile device.

TROPICAL ROOFING PRODUCTS WELCOMES NEW SALES REPRESENTATIVES

Published July 8th, 2016 by Edward Leshansky

TROPICAL ROOFING PRODUCTS WELCOMES NEW SALES REPRESENTATIVES

Strengthening Resources for Growth-Oriented Company

PORT ARTHUR, TX – Tropical Roofing Products announces the addition of 3 Sales Representatives to cover Texas and surrounding states. 

Logan Baird, based in the Dallas area, comes to Tropical Roofing Products with over 10 years of experience in the building and roofing industry, having previously worked as a Sales Manager, National Accounts Manager and Territory Manager.

Shana Durkee, also to be based in the Dallas area, joins Tropical Roofing Products and brings 8 plus years of industry experience and over 20 years of Sales Management, achieving several sales accolades such as Salesperson of the Year and President’s Club honors.

Jonathan Haro, will be based in the Houston area and brings several years of Sales and industry experience to this new position.

“We are very excited about the addition of these exceptional Salespeople, which allows Tropical Roofing Products to better service Texas and surrounding states,” said Michael King, Vice President of Sales.

Tropical Roofing Products views these appointments as a sign of our commitment to being a leading supplier to our industry.  The growth of our Fluid Applied Restoration Systems and the increasing demands of our customers led us to look for the right additions to our team who will fit in with our ethos of innovation and exceptional service.”

For more information on Tropical Roofing Products, or to find your closest representative, call 800-432-2855 or visit www.tropicalroofingproducts.com. Download the Tropical Roofing Products dynamic mobile app by texting “ROOFING” to 94502 or visit the app store for your mobile device.